Orientating each insert with the notch at the bottom makes it easier to locate the notch when a photogate peg is used. nut insert Note: There is a notch on the inside of the inserts which allows the photogate pegs to be keyed into the insert to prevent rotation. The inserts should be inserted in from the white side of the panel (See Figure 1).
Pasco smart timer me 8930 install#
a) To install the inserts, press one plastic insert into each of the 70 holes in the three boards. This is a one-time installation, as the inserts are a permanent part of the support panels. Plugging in the Hole Inserts (one-time installation): To prepare the ME-9812 for first use, the hole inserts must be plugged into the holes. 4Ħ Introduction The ME-9812 PASCO has loops and hills for studying conservation of energy and centripetal acceleration, a straight track for collisions, and a brachistochrone to demonstrate the path of least time. Data collection interface (ScienceWorkshop interface, USB links with or without PASPORT Xplorers) CI-6450 or PS-2100 or PS-2000 *Use Replacement Model Numbers to expedite replacement orders.
Pasco smart timer me 8930 software#
DataStudio software (version 1.6 or later) Various (See PASCO catalog). Smart Timer ME Projectile Mini-Catcher Accessory or Projectile Catcher Accessory ME-6814 or ME Rotating Platform ME Photogate/Pulley System ME Super Pulley with Clamp ME-9448A 23. Catchers (2) Track couplers (2) Hole inserts (70) Hole insert nuts (70) Peg clips (50) Short pegs 7.4 cm length (3) Long pegs 16.2 cm length (40) Photogate mounting pegs (4), 18.9 cm length Photogate brackets (4) Ballast masses for mini-cars (3) mass= 0.04 kg ea Water cups (3) Rubber bands (1 package with 2 lengths) and Optional Equipment (for experiments) Model Number 21. ME Flags for Mini-Cars (3) (Equipment list continued on next page) 3ĥ Equipment List (Continued) Included Equipment Model Number 9. Track (1 coil), 9.1 meters, 5.1 cm width Support Panel (left), white (1), 85.9 cm x 60.4 cm Support Panel (center), white (1), 52.8 cm x 60.4 cm Support Panel (right), white (1), 85.9 cm x 60.4 cm Support Feet (4) Collision Accessory (3) with 6-32 screws (3) Mini-Cars (3): 1 red, 1 green, and 1 yellow mass = 0.18 kg ea.
Brachistochrone (at different start positions) Acceleration Down Different Inclined Tracks Collisions on a Level Track Acceleration of Car by Mass on String over Pulley Projectile Car Off End of Track (3 different steps) Projectile Car Off End of Track after Colliding Oscillations in a Well Conservation of Angular Momentum Position, Velocity, Acceleration Circular Track High Road and Low Road APPENDIX A: Technical Support APPENDIX B: Copyright and Warranty InformationĤ Equipment List Included Equipment Replacement Model Number* 1. 5 TRACK ASSEMBLY Plugging in the Hole Inserts Using Support Feet with the Panels Attaching the Track to the Panels Attaching Photogates to the Track Attaching the Catcher to the Track Using the Track without the Panels CAR ASSEMBLY OPTIONS Wheel Labels Bumper (elastic and inelastic) Photogate Flag Adding a Ballast Mass and Additional Masses Coupling Three Cars Stacking Two Cars Car Center of Mass SUGGESTED EXPERIMENTS (WITH CONFIGURATIONS) Loop (One Car) Cup of Water Over Loop Three-Car Coaster Collision Between Two Cars at Bottom of Loop Conservation of Energy (Hills) Conservation of Energy (Step) Brachistochrone vs.
3 Table of Contents EQUIPMENT LIST INTRODUCTION.
0 kommentar(er)
